EasyStand Evolv El manual del propietario

Owner’s Manual™™Large

page 7 pConfiguration Assembly-GliderConfiguration Assembly-EasyStand®Glider™FIG. 8FIG. 7

page 8Configuration Assembly-GliderFIG. 8FIG. 7FIG. 7- Slide the front Glider column into the opening of the mainframe as shown. Install the four bolt

FIG. 9FIG. 9FIG. 10FIG. 10FIG. 11FIG. 11FIG. 12FIG. 13FIG. 15FIG. 15FIG. 14Configuration Assembly-EasyStand®Shadow Support Traypage 9 pConfiguration

page 10Configuration Assembly-Shadow Support TrayFIG. 12FIG. 13FIG. 14FIG. 15FIG. 9- Attach the axle weldment to the front column with bolts and tight

page 11 pOption AssemblyOption Assembly-Back Option AssemblyBack OptionAssembly

Contoured Backspage 12Option AssemblyHighContouredBackNG50068LowContouredBackNG50062

Pump Handlespage 13 pOption AssemblyRemovableActuator HandleNG50035T-StyleHandleExtensionNG50070Quad GripHandleExtensionNG50044

Foot Straps and Airline Buckle Hip Beltpage 14Option AssemblySecure FootStrapsNG30031Standard FootStrapsNG30030Airline BuckleHip BeltNG30028

page 15 pOption AssemblyChest Vests and Chest StrapsY-StyleChest VestNG30021X-StyleChest VestNG30056Chest StrapNG50192-SmallNG50193-Large

page 16Option AssemblyAngle Adjustable Tray, Chest Pad and Head SupportChest PadNG30000not available w/theNG50024 GliderAngle Adjustable TrayNG50043no

800-342-8968 www.easystand.com

Independent Knee and Roho®Seatpage 17 pOption AssemblyRoho®SeatNG30023Independent Knee NG50080not available w/the NG50026 Glider

page 18Option AssemblyUniversal Lateral Supports Receiver and Lateral SupportsUniversal LateralSupports ReceiverNG50041LateralSupportsNG50176

page 19 pOption AssemblyHip Supports and Head SupportHip SupportsNG50198HeadSupportNG50037

page 20Reference Drawing-EvolvBasic Unit Reference Drawing-EasyStand®Evolv™

page 21 pEvolv Options & Parts DetailEasyStand®Evolv™Options & Parts Detail

Evolv Options & Parts Detailpage 22

page 23 pAdjusting Your EvolvFootplatesFIG. A- Loosen the clamp connecting the foot bracket to the seat post. Adjust the height of the foot bracket so

page 24Adjusting Your EvolvFIG. FFIG. GSeat Depth/Back AngleFIG. F- Loosen the two clamp knobs located on each of the seat tubes under the seat. Do NO

page 25 pPerfect Fit GuideProper positioning is needed to obtain optimum standing posture.Measure client for approximate seat depth (A)and footplate (

page 26Configuration AdjustmentsFIG.A-To adjust the handle height, loosen the clamp. Adjust the handle height to theuser’s desired position and tighte

Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Safety Precautions . . . . . . . . . . . . . . . . . . . . . .

page 27 pConfiguration AdjustmentsEasyStand®Shadow Support Tray AdjustmentsFIG. A- To adjust the table depth, loosen the knoband lift slightly on the

page 28Transferring & StandingTransferring• For proper transfer techniques, please seek professional advice from your therapist or physician.• The

• Clean the EasyStand Evolv with a mild non-abrasive disinfectant or soap and water.• Check your EasyStand periodically to make sure that all nuts, bo

page 30SpecificationsEvolv-Basic UnitEvolv-Glider5’0”-6’2”280 lbs.16”-21”18”-23”15”-18”22.5”4”-14”15.5”-30”10”25”-40”175 lbs.CharcoalBlack7.5”x19”Heig

page 31 Standing Log

page 32WarrantyLimited WarrantyThis warranty is extended only to the original purchaser/customer (or supplier non consumer who does not buy orresell).

Toll Free: 800.342.8968 or 507.697.6393Fax Free: 877.342.8968 or 507.697.6900email: [email protected] Standing technology should

Congratulations on your purchase of the Easystand Evolv standing frame! We at AltimateMedical have designed the EasyStand Evolv with your comfort and

• The EasyStand Evolv (Large) is designed to accommodate most individuals from 5’- 6'2" (152cm-188cm) and up to 280 lbs (127kg). If you do n

Basic Unit Assembly-EasyStand®Evolv™FIG. 1FIG. 2FIG. 3FIG. 3FIG. 5page 3Basic Unit Assembly-EvolvVideos on EasyStand Evolv assembly & fitting can

page 4Basic Unit Assembly-EvolvFIG. 1FIG. 2FIG. 2FIG. 3Front ColumnMain FrameNote: Bolts are currently in proper location.FIG. 1- Attach the axle weld

FIG. 5FIG. 6page 5 pBasic Unit Assembly-EvolvFIG. 4

page 6Basic Unit Assembly-EvolvFIG. 4FIG. 6FIG. 5FIG. 4- Place kneepad onto knee bracket. Insertbolts and tighten securely.FIG. 5- Insert the tray pos